LimePath
GeoSuDS UV

You are here:

LimePath GeoSuDS UV is a UV stable Resin Bound Surfacing system which is installed at 30mm/40mm depth onto a 4mm high performance triple layer system of geotextiles & a stabilisation geonet. This system reduces the need for a binder courses such as concrete and asphalt concrete (macadam) whilst still providing high permeability & strength. The structure allows rainwater to pass through being SuDS (Sustainable Urban Drainage Systems) compliant. With permeability rates of up to 850l/m²/m. LimePath GeoSuDS UV has a triple lock stabilisation layer which is thermally bonded on both sides to provide excellent drainage & filtration whilst helping to stabilize the decorative UV Resin Bound surface layer and Sub-base.

Available in a variety of colours LimePath GeoSuDS UV is ideal for both commercial & domestic pathways, nature walks and general pedestrian areas.

DOWNLOADS

  • Technical Data Sheet
  • Colour Swatch (Mix Blends)
  • Base build ups
  • Additional information

Technical Data Sheet

  • LimePath GeoSuDS UV
  • Slip Resistance

All LimePath GeoSuDS UV aggregate blends have been tested for slip resistance in wet and dry conditions.
Anti-Slip aggregate broadcast onto the surfacing during installation will significantly increase the slip resistance of the surface in the wet and on steep gradients without substantial change to appearance.

Services available

  • Technical Support
  • Installation and Setup
  • Maintenance
  • Application Support
  • Hardware Support
  • Guaranteed Warranty

Resin & aggregate

LimePath GeoSuDS UV resin is a UV resistant resin and will not yellow on exposure to UV light. This is a more attractive option than some other types of resin which can yellow and dramatically alter the appearance of the finished surface. The resin is formulated using aliphatic HDI which will not deteriorate or become brittle when exposed to UV light when tested to BS EN ISO 16474-3 method A The performance and appearance of the finished surface is dependent on the aggregate used (see LimeGate Solutions LimePath GeoSuDS UV mix blend swatch sheet for colour options). The LimePath GeoSuDS UV Aggregate blends have been designed to achieve strength, resilience, porosity and decoration.

Please Note:

Natural aggregates may contain small amounts of iron which can produce rust staining when exposed to air and water; standard LimePath GeoSuDS UV blends contain aggregates selected for infrequency of incidence of staining but iron may be present in any natural aggregate. The presence of iron cannot be identified before use and Limegate Solutions cannot accept responsibility for any loss or damage suffered as a result of staining.

Shelf Life & Storage

Shelf life of LimePath GeoSuDS UV Resin is 6 months, Aggregates & GeoNet have an unlimited shelf life. Store materials in clean, dry, frost free warehouse conditions between 5°C and 25°C.
Protect from sunlight.

Features and benefits

  • UV stable will not discolor or degrade
  • Tested to slip resistant BS 8204-6
  • SuDS compliant permeable paving 850 liters/m²/minute
  • Natural & Recycled aggregate available
  • 30mm/40mm depth install directly onto type 1 or 3
  • Triple lock GeoNet to help base stabilization and water drainage
  • All aggregates selected to reduce chances of rust appearing
  • Foot traffic after 14-15 hours @ 20°c
  • Manufactured to ISO 9001
  • Made in UK

LimePath GeoSuDS UV Contractors

LimePath GeoSuDS UV is a specialist product and must only be applied by specialist applicators. Do not apply or allow it to be applied by contractors who do not possess the necessary experience. You should consider appointing a Limegate Solutions Approved Contractor.

Shelf Life & Storage

Shelf life of LimePath GeoSuDS UV Resin is 6 months, Aggregates & GeoNet have an unlimited shelf life. Store materials in clean, dry, frost free warehouse conditions between 5°C and 25°C.

Protect from sunlight.

Mix Design & Pack Sizes

7.5kg

LimeBound Resin Bound Surfacing Resin

100kg (4x 25kg bags)

LimeBound Resin Bound Surfacing Aggregate

6.25kg

LimeBound Fine Aggregate

2m x 50mm x 4mm Rolls (100m²)

GeoNet

Health & safety

Please refer to Limegate Solutions LimePath GeoSuDS UV Safety Data Sheet.

Download Centre

Coverage

Coverage rates for individual blends can vary. Please refer to the Limegate Solutions LimePath GeoSuDS UV Mix Blend & Aggregate sheet. Coverage is based on application to a smooth flat surface and will vary when applied to undulating surfaces, according to compaction, and to the aggregate grading, which can change from batch to batch. Please contact us if you have any queries.

Working Times & Temperatures

Working time is affected by temperature; at temperatures above the maximum recommended 25°c the pot life and working time may be insufficient to allow a wet edge to be maintained. Do not therefore proceed when product and/or air temperature exceeds recommendations. The air temperature must be monitored during application and work should stop when the temperature exceeds recommendations. Care must be taken to keep materials as cool as possible in warm weather.
At low temperatures 5°C and below the resin will not flow sufficiently to achieve a smooth finish and work should not proceed.

Substrate Requirements

LimePath GeoSuDS UV System is designed for foot traffic and after consultation occasional vehicle access traffic such as light infrequent maintenance vehicles or pedestrian two wheel mode of transportation. All resin bound products by nature will be vulnerable to heavy impact and high point loading. It is good practise that the product is subject to cleaning and maintenance and regularly inspected by the client or installer and maintained as required. Please see LimePath GeoSuDS UV O&M Manual for further maintenance information.

Please refer to:
Limegate Solutions LimePath GeoSuDS UV Base Build Up Sheets for individual substrate requirements

Site Attendance

When on site Limegate Solutions representatives are if asked, able to give a general indication of the correct method of installing Limegate Solutions products. It is important to bear in mind that Limegate Solutions is a supplier and not an application contractor and it is therefore the responsibility of the contractor and his employer to ensure he is aware of the correct practices and procedures to ensure the correct installation of the product and that liability for its correct installation is with the contractor and not with Limegate Solutions Ltd.

Product

Product: LimePath GeoSuDS UV
Thickness: 30mm/40mm LimePath GeoSuDS surface course (dependant on required usage)
Aggregate: (select mix blend as required)
Installation: Limegate Solutions Approved FeRFA association member contractor

Supplier:
Limegate Solutions Ltd
Unit 6
Murray Road
Orpington
Kent
BR5 3RE

Tel: 01959 546208
email:

contact-ico

Contact us to ask any questions to help in specifying the right system:

Get in touch

If you have any questions about our product range, a member of our experienced team will be happy to help.